Siemens 6ES7193-1FH30-0XA0 – SIMATIC DP add-on terminal 2-tier, 16 channels, for ET 200L, screw terminals
Siemens 6ES7193-1FH30-0XA0 – ET200L Add.Term. 2 Rows,16ch Screw-Type from the SIMATIC S7 range. Status: discontinued by the manufacturer, no longer available new since October 2024. Van Haelen supplies it refurbished or new in sealed factory packaging, with a 24-month warranty.
Also written as: 6ES7 193-1FH30-0XA0, 6ES71931FH300XA0
The Siemens 6ES7193-1FH30-0XA0 is the SIMATIC DP add-on terminal with 2 tiers and 16 channels for the ET 200L, with screw terminals. The add-on terminal plugs onto the terminal block of the ET 200L station and gives each channel two extra connection terminals, so sensors and actuators with three- or four-wire connection can connect their supply and ground wire directly to the station without separate distribution terminals in the cabinet; the conductors are fixed in the screw terminals. Siemens keeps this type as a spare part, reports it as no longer available and discontinued it on 1 October 2024; no successor is specified. When replacing, switch the station off, carry over the wiring terminal by terminal, plug the new terminal row onto the terminal block in the same place and check the connections; the versions with one tier and with spring terminals have different order numbers.
Available as
Product data
| Manufacturer | Siemens |
|---|
| Part number | 6ES7193-1FH30-0XA0 |
|---|
| Type designation | ET200L Add.Term. 2 Rows,16ch Screw-Type |
|---|
| Series | SIMATIC S7 |
|---|
| Manufacturer status | discontinued by the manufacturer, no longer available new since October 2024 |
|---|
| ETIM | EC001599 |
|---|
| HS code | 85369010 |
|---|
| Country of origin | DE |
|---|
| Weight | 0,171 kg |
|---|
Documentation from the manufacturer
All products of the SIMATIC S7 series
All PLC I/O modules
Faults and fixes 6ES7193-1FH30-0XA0
Problems with 6ES7193-1FH30-0XA0: BF LED, station unreachable
On an ET 200 interface module BF indicates a bus fault: on PROFINET a missing or wrong device name and IP setting, on PROFIBUS a wrong address or a cable without termination. After replacement the device name must be assigned again (TIA: Online, assign device name) or the PROFIBUS address switch set to the same position. SF with BF off points to a module in the station: wrong module, missing module or a channel diagnostic.
6ES7193-1FH30-0XA0: module drops out under vibration or heat
In distributed stations contact problems on the terminal or base module and overheating in the cabinet are the most common causes of sporadic drop-outs. Check the module's latch on the base module, the earth rail and the cabinet temperature. If the station keeps dropping out at the same module, replace that module.
Fault not fixed: replace, exchange or repair the 6ES7193-1FH30-0XA0?
Replacing from stock is the fastest route when a machine is down. Van Haelen supplies the 6ES7193-1FH30-0XA0 refurbished (tested, with a test report per serial number) or new in factory packaging, with a 24-month warranty. The current lead time is shown with the condition on this page. Prefer an exchange: you get a refurbished unit straight away and return the faulty one within 14 days. Repairing your own unit is also possible: diagnosis, then a fixed price.
What information should I send for a quick diagnosis?
A photo of the rating plate (order number, product version, firmware), the exact fault code or LED state, when the fault occurs (at power-up, on enable, under load) and what you have already tried. For PLCs an export of the diagnostic buffer, for drives the parameter set. With that we can usually say the same day whether replacing, exchanging or repairing is best.
Frequently asked questions
Is the 6ES7193-1FH30-0XA0 still available?
Not new from the manufacturer any more: the 6ES7193-1FH30-0XA0 was discontinued since October 2024. Van Haelen supplies it refurbished and tested.
What does refurbished mean?
Cleaned, inspected, aged or critical components replaced and tested to our test protocol for this product family. You get a 24-month warranty, a test report and a serial number label.
What do I check when replacing a 6ES7193-1FH30-0XA0?
Check the product version (issue) on the rating plate; for most installations the same or a higher issue is suitable.
Can I exchange or repair my faulty unit?
Yes. With an exchange Van Haelen supplies a refurbished unit straight away and you return the faulty one. With a repair you first get a diagnosis and then a fixed price, with test report and warranty.