Lenze EVS9324-EP – 9300 servo position controller 3 kW, 320-528 V, IP20
Lenze EVS9324-EP – Position controller from the 9300-Series range. Status: in phase-out at the manufacturer. Van Haelen supplies it refurbished or new in sealed factory packaging, with a 24-month warranty.
Also written as: EVS9324EP
The Lenze EVS9324-EP is the 9300 series servo position controller with 3 kW, three-phase mains 320-528 V at 45-65 Hz and degree of protection IP20. The position controller has a built-in positioning function, so the axis moves to its positions without a separate positioning control. The Lenze 9300 series comprises servo inverters, position controllers, cam profilers and frequency inverters for control cabinet mounting; an identical type replaces a defective unit without changing the machine. According to the product data the type is phasing out; no successor is specified. When replacing, switch off the mains and wait for the DC link discharge time, mount the unit in the same place, connect the mains, motor and control cables to the same terminals, transfer the parameter set of the old unit and after switching on check the operation.
Available as
Product data
| Manufacturer | Lenze |
|---|
| Part number | EVS9324-EP |
|---|
| Type designation | Position controller |
|---|
| Series | 9300-Series |
|---|
| Manufacturer status | in phase-out at the manufacturer |
|---|
| ETIM | EC001857 |
|---|
| HS code | 85044095 |
|---|
| Weight | 5,4 kg |
|---|
| Dimensions | 10,20 x 35,60 x 25,40 cm |
|---|
Documentation from the manufacturer
All products of the 9300-Series series
All Servo drives and amplifiers
Faults and fixes EVS9324-EP
Problems with EVS9324-EP: OC1, OC5, OU, LU or OH
On Lenze 8200, 9300 and smd OC1 is a short circuit on the motor side, OC2 an earth fault, OC5 the I×t overload, OU DC-link overvoltage (decelerating too fast), LU undervoltage (mains gone or sagging) and OH heat sink overtemperature; OH3 is the motor PTC. If OC1 appears immediately on enable without a motor, the output stage is defective.
What do I check when replacing a EVS9324-EP?
Read out the parameter set with Global Drive Control or the keypad and note the function module (standard I/O, INTERBUS, PROFIBUS, system bus); it defines how the drive sits in the installation. Rating, voltage and software version must match the set. On 9300 servo drives check the resolver or encoder setting and the motor data before enabling.
Fault not fixed: replace, exchange or repair the EVS9324-EP?
Replacing from stock is the fastest route when a machine is down. Van Haelen supplies the EVS9324-EP refurbished (tested, with a test report per serial number) or new in factory packaging, with a 24-month warranty. The current lead time is shown with the condition on this page. Prefer an exchange: you get a refurbished unit straight away and return the faulty one within 14 days. Repairing your own unit is also possible: diagnosis, then a fixed price.
What information should I send for a quick diagnosis?
A photo of the rating plate (order number, product version, firmware), the exact fault code or LED state, when the fault occurs (at power-up, on enable, under load) and what you have already tried. For PLCs an export of the diagnostic buffer, for drives the parameter set. With that we can usually say the same day whether replacing, exchanging or repairing is best.
Frequently asked questions
Is the EVS9324-EP still available?
The manufacturer has put the EVS9324-EP in phase-out; new units are getting scarce. Van Haelen supplies it from stock.
What does refurbished mean?
Cleaned, inspected, aged or critical components replaced and tested to our test protocol for this product family. You get a 24-month warranty, a test report and a serial number label.
Can I exchange or repair my faulty unit?
Yes. With an exchange Van Haelen supplies a refurbished unit straight away and you return the faulty one. With a repair you first get a diagnosis and then a fixed price, with test report and warranty.